Emulex 375 User Manual Page 38
- Page / 78
- Table of contents
- BOOKMARKS
Rated. / 5. Based on customer reviews
EMULEX MODEL 375 SAN STORAGE SWITCH
USER’S GUIDE CHAPTER 3: SWITCH MANAGEMENT
EMULEX CORPORATION 35
P
ART NUMBER 00041369-002 REV. B
Change Notifications
The following settings are available.
Setting Description
Stealth Intelligent Change
Manager
Stealth Intelligent Change Manager provides stability and control
over change notification disruptions on a port basis. Options
include:
• Off: No Change Protection – no Stealth Intelligent Change
Manager control.
• Initiator: Only Receive Changes – devices attached to the port
can receive change notifications but will not propagate change
notifications generated by that port to other ports.
• Target: Only Send Changes – propagates change notifications
generated by the port to other ports but will not allow devices
attached to the port to receive change notifications from other
ports.
• Switch-Switch: Send and Receive Changes – allows change
notifications to propagate between switches.
• Custom-1 – Note: This setting should not be used unless
directed to do so by a customer service representative.
Change Notification on
Insertion
The switch normally operates under the condition that when a
device is inserted onto the network, a change notification is
generated. However, this condition is not always true when
connecting hubs or switches together. In some instances, it is
possible to connect two zones together without the zones realizing
that multiple AL_PAs exist with the same values.
When this policy is enabled, the switch always generates a change
notification to ensure that the proper system updates are performed.
However, when a device is removed (for example, an initiator or
target), the removal does not generate a change notification and
there are no system updates performed.
Change Notification on
Remova
l
This policy is similar to the Change Notification on Insertion policy,
except for the change notification being sent when a device is
removed rather than inserted.
When this policy is enabled, the switch always generates a change
notification to ensure that the proper system updates are performed.
- User’s Guide 1
- USER’S GUIDE 2
- EMULEX CORPORATION I 2
- Table of Contents 3
- ECHNICAL SUPPORT 4
- OVERVIEW 5
- NSPEED™ TECHNOLOGY 6
- WITCH APPLICATIONS 7
- Tape Library Consolidation 8
- Rich Media 9
- Server Clustering 9
- NSTALLATION PREPARATION 10
- WITCH INSTALLATION 11
- Safety & Regulatory Guide 11
- EMULEX CORPORATION 9 12
- NUMBER 00041369-002 REV. B 12
- SWITCH LEDS 13
- System LEDs 14
- Port LEDs 14
- Power Supply/Fan Module LED 15
- OMPATIBILITY 16
- If the SFP has a removal tag 16
- OOTING THE SWITCH AND SAN 17
- EMULEX CORPORATION 15 18
- CHAPTER 3SWITCH MANAGEMENT 19
- GETTING STARTED 20
- Connecting to the Web Manager 21
- Web Manager Overview 21
- Documentation 22
- Initial Switch Setup 23
- CHAPTER 3: SWITCH MANAGEMENT 24
- ANAGING THE SWITCH 25
- Figure 3-2: Switch Login page 26
- Switch Identification 27
- Network Location 27
- Version Information 28
- Switch Speed 28
- Blocking ARB 28
- Agent Up Time 28
- Setting SNMP Traps 29
- Emulex® or InSpeed™ Storage 31
- EMULEX CORPORATION 29 32
- Default Smart Settings 34
- Smart Setting Assignments 36
- Port Information 37
- Pre-Insertion Testing 37
- Change Notifications 38
- Port Recovery 39
- Diagnostics 40
- Switch Firmware Files 41
- Switch Configuration Files 42
- One-Step Zoning 43
- Single-Switch Zoning 44
- Multiple Switch Zoning 46
- Emulex® or 47
- Cascading Switches 49
- Automatic Trunking 50
- Load Balancing 51
- Load Indicators 52
- ONITORING THE SWITCH 53
- EMULEX CORPORATION 51 54
- Port Utilization and Health 55
- Viewing the Event Log 56
- Viewing Port Information 57
- Viewing Port Utilization 58
- Viewing Port Diagnostics 59
- Manual Port Operation 60
- Viewing Ordered Sets 61
- EMULEX CORPORATION 59 62
- CHAPTER 4TECHNICAL REFERENCE 63
- EMULEX CORPORATION 61 64
- EMULEX CORPORATION 62 65
- FIBRE CHANNEL REFERENCES 66
- Appendixes 67
- WITCH SPECIFICATIONS 68
- PERATING CONDITIONS 68
- PPENDIX B CLI Quick Reference 69
- USING THE CLI 70
- CLI COMMANDS 71
- APPENDIX C Event Messages 72
- EMULEX CORPORATION 70 73
- EMULEX CORPORATION 71 74
- APPENDIX E Glossary 75
- USER’S GUIDE INDEX 76
- EMULEX CORPORATION 73 76
- EMULEX CORPORATION 74 77
- EMULEX CORPORATION 75 78
Related products and manuals for Hardware Emulex 375
Hardware Emulex Adapters User Manual
(24 pages)
(24 pages)
© 2020, manymanuals.com. All rights reserved. | 0.674 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comments to this Manuals