Emulex 375 User Manual Page 17
- Page / 78
- Table of contents
- BOOKMARKS
Rated. / 5. Based on customer reviews
EMULEX MODEL 375 SAN STORAGE SWITCH
USER’S GUIDE CHAPTER 2: SWITCH INSTALLATION
EMULEX CORPORATION 14
P
ART NUMBER 00041369-002 REV. B
BOOTING THE SWITCH AND SAN
The following procedure is recommended when booting the switch and SAN. Before powering on the
switch and SAN, read the Release Notes, included with the switch contents, to determine any
modifications that may be required for a specific installation.
To boot the switch and SAN:
1. Power on the storage devices (such as JBODs, tape libraries, and RAIDs).
2. Insert the plug end of the switch’s power cord to a properly grounded power source.
3. Insert the power cord’s IEC connector end into the switch’s power receptacle.
The switch powers on and runs Power-On Self-Test (POST) diagnostics to verify the
fundamental integrity of the switch ports. All switch LEDs turn on (LEDs illuminate). Then,
excluding the Ethernet Link, Power Supply/Fan Module, and Power LEDs, the LEDs turn off
(LEDs extinguish). Once the switch is operational, the LEDs display current status as described
in “Switch LEDs” on page 10.
4. Power on any other switches connected to the SAN.
5. For certain applications, switch configuration must be completed before continuing with the next
step. For information regarding switch configuration, see Chapter 3: Switch Management.
6. After all switches have initialized, power on the hosts.
The network initializes.
7. Check all port LEDs.
The SAN should be fully operational at this point. However, it is appropriate to ensure that
proper discovery has taken place and all required devices are participating in the network. Some
host bus adapters may provide this level of functionality or it might be resident in the application
software on the host operating system.
Note: The power cord’s IEC connector plug serves as the switch’s disconnect device. To
cycle power to the switch, remove and reconnect the switch’s power cord.
Note: FC-AL compatible nodes must perform initialization procedures upon power-up in
order to function properly. It is the responsibility of the Fibre Channel driver software
on FC-AL nodes to perform this initialization.
- User’s Guide 1
- USER’S GUIDE 2
- EMULEX CORPORATION I 2
- Table of Contents 3
- ECHNICAL SUPPORT 4
- OVERVIEW 5
- NSPEED™ TECHNOLOGY 6
- WITCH APPLICATIONS 7
- Tape Library Consolidation 8
- Rich Media 9
- Server Clustering 9
- NSTALLATION PREPARATION 10
- WITCH INSTALLATION 11
- Safety & Regulatory Guide 11
- EMULEX CORPORATION 9 12
- NUMBER 00041369-002 REV. B 12
- SWITCH LEDS 13
- System LEDs 14
- Port LEDs 14
- Power Supply/Fan Module LED 15
- OMPATIBILITY 16
- If the SFP has a removal tag 16
- OOTING THE SWITCH AND SAN 17
- EMULEX CORPORATION 15 18
- CHAPTER 3SWITCH MANAGEMENT 19
- GETTING STARTED 20
- Connecting to the Web Manager 21
- Web Manager Overview 21
- Documentation 22
- Initial Switch Setup 23
- CHAPTER 3: SWITCH MANAGEMENT 24
- ANAGING THE SWITCH 25
- Figure 3-2: Switch Login page 26
- Switch Identification 27
- Network Location 27
- Version Information 28
- Switch Speed 28
- Blocking ARB 28
- Agent Up Time 28
- Setting SNMP Traps 29
- Emulex® or InSpeed™ Storage 31
- EMULEX CORPORATION 29 32
- Default Smart Settings 34
- Smart Setting Assignments 36
- Port Information 37
- Pre-Insertion Testing 37
- Change Notifications 38
- Port Recovery 39
- Diagnostics 40
- Switch Firmware Files 41
- Switch Configuration Files 42
- One-Step Zoning 43
- Single-Switch Zoning 44
- Multiple Switch Zoning 46
- Emulex® or 47
- Cascading Switches 49
- Automatic Trunking 50
- Load Balancing 51
- Load Indicators 52
- ONITORING THE SWITCH 53
- EMULEX CORPORATION 51 54
- Port Utilization and Health 55
- Viewing the Event Log 56
- Viewing Port Information 57
- Viewing Port Utilization 58
- Viewing Port Diagnostics 59
- Manual Port Operation 60
- Viewing Ordered Sets 61
- EMULEX CORPORATION 59 62
- CHAPTER 4TECHNICAL REFERENCE 63
- EMULEX CORPORATION 61 64
- EMULEX CORPORATION 62 65
- FIBRE CHANNEL REFERENCES 66
- Appendixes 67
- WITCH SPECIFICATIONS 68
- PERATING CONDITIONS 68
- PPENDIX B CLI Quick Reference 69
- USING THE CLI 70
- CLI COMMANDS 71
- APPENDIX C Event Messages 72
- EMULEX CORPORATION 70 73
- EMULEX CORPORATION 71 74
- APPENDIX E Glossary 75
- USER’S GUIDE INDEX 76
- EMULEX CORPORATION 73 76
- EMULEX CORPORATION 74 77
- EMULEX CORPORATION 75 78
Related products and manuals for Hardware Emulex 375
Hardware Emulex Adapters User Manual
(24 pages)
(24 pages)
© 2020, manymanuals.com. All rights reserved. | 0.566 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comments to this Manuals